KRISS Vector grouping

View previous topic View next topic Go down

KRISS Vector grouping

Post by Solscud007 on Sun Apr 08, 2012 8:13 pm

I will add groupings that we get and keep them in one post here.

PNW KRISS Vector Groupings

SBR 25yd


SBR 50yd


SBR 100yd


CRB 25yd


CRB 50yd


CRB 100yd





Alcat's KRISS Vector CRB Groupings

25yd



50yd


50yd WWB with wind


50yd South African Ammo with wind


_________________
Most of the information I find and collect about the Kriss is documented on my facebook page.
http://www.facebook.com/pages/Kriss-Super-V/157275704339968
avatar
Solscud007
MOD

Posts : 1580
Join date : 2012-01-05
Age : 37
Location : Pittsburgh, PA

http://www.facebook.com/pages/Kriss-Super-V/157275704339968?sk=w

Back to top Go down

Re: KRISS Vector grouping

Post by Solscud007 on Fri Jun 22, 2012 11:24 am

A short test of match reloads vs PNW arms with my KRISS Carbine. At 25 yds.


_________________
Most of the information I find and collect about the Kriss is documented on my facebook page.
http://www.facebook.com/pages/Kriss-Super-V/157275704339968
avatar
Solscud007
MOD

Posts : 1580
Join date : 2012-01-05
Age : 37
Location : Pittsburgh, PA

http://www.facebook.com/pages/Kriss-Super-V/157275704339968?sk=w

Back to top Go down

Re: KRISS Vector grouping

Post by AZ2000 on Tue Sep 11, 2012 11:09 pm

Hi shooters, went out again today to try some more 25yd, 50yd and 100yd groups. Was not real hot 72, but was raining a bit. Used 230 grain BVAC factory rnd nose again and ran another 100 through the weapon as I do the, "no clean it test" up to the 1,000 round mark. Should be about 600 to this point. Had one failure to eject but that was a limp wrist on my part, not paying attention, just getting wet. Wind was about 4-5 mph from right to left at about 45 degrees from the back. Re-mounted and shimmed the red dot, so had to spend a little time re-zeroing it in @ about 3 inches low for 25 yrds to compensate for a closer 50 yd zero. I forgot to bring the good camera again, so had to use my phone. Guess I will have to just put it in the truck so next time I have it? attention The 25 yd was with 5 rounds elbows on a bench, the 50 yd was with 8 and elbows on a bench and the same for the 100yd 9 rounds. Not sure if you can see it with these pictures, but I put a small blue dot on the top right corner of the 100yd target which was my POA, to compensate for the wind and drop, about 12 to 14 inches @ 100yds. I know this is a CQW, but I sure enjoy seeing what I can do with this thing and what it will do. I am thinking maybe a fast draw holster, to go along with my Colt .45. justkidding Here are some pics, hopefully mambro will see this and make the little guys bigger. Oh yeah, the target is a 12" diameter circle with a 1" center.


100 yd


50 yd


25yd


Last edited by AZ2000 on Tue Sep 11, 2012 11:15 pm; edited 2 times in total (Reason for editing : additional comments)
avatar
AZ2000

Posts : 197
Join date : 2012-08-09
Location : AZ

Back to top Go down

Re: KRISS Vector grouping

Post by Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum